3D Systems CubePro 3D Printer Скачать руководство пользователя

Страница: 24 / 110

MENU OVERVIEW

Touchscreen Display

After powering on the printer and turning on the touchscreen display, touch the display to continue.

CAUTION: When using the touchscreen, use only light ﬁnger pressure to make

selections. Using anything sharp will damage the touchscreen display and will void the

manufacturer’s warranty.

Print / Setup

PRINT

allows the user to print a creation stored either on a USB mass storage device or from the CubePro

software.

SETUP

allows the user to conﬁgure the printer, connect to a wireless or ad hoc network, install cartridges,

or view the printer status.

Navigation

Navigation between screens is performed by pressing the right or left arrows.

Materials

CARTRIDGE STATUS

allows the user to view the type and color of the material that is installed. It also

displays the estimated amount of material left in the cartridge.
Selecting

CHANGE CARTRIDGE

allows the user to install cartridges in empty bays or replace installed

cartridges.

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

Похожие инструкции для CubePro 3D Printer

Бренды по названию

Популярные бренды

3D Systems CubePro 3D Printer, Руководство пользователя

Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

Похожие инструкции для CubePro 3D Printer

Бренды по названию

Популярные бренды