3D Systems CubePro 3D Printer Скачать руководство пользователя

Страница: 6 / 110

IMPORTANT SAFETY INFORMATION

Safety Symbols and Deﬁnitions

HOT SURFACE HAZARD: A HOT SURFACE IS ACCESSIBLE IN THE VICINITY OF THIS SIGN

OR AT THE PRINT JET. AVOID CONTACT WITH THESE AREAS. HOT SURFACES CAN CAUSE

SEVERE BURNS.
Caution: Indicates something may happen that could cause loss of data, damage to

equipment, or could cause personal injury.

Caution: Indicates a pinch point hazard that could cause personal injury.

SHOCK WARNING: INDICATES A POTENTIAL SHOCK HAZARD.

SAFETY GUIDELINES

Follow all safety rules in this section and observe all cautions and warnings in this guide.

Do not modify any safety features or make modiﬁcations to the CubePro. Doing so is prohibited and voids the warranty.

Use of print materials other than genuine 3D Systems components may void the warranty.

WARNING: HAZARDOUS MOVING PARTS. KEEP FINGERS AND OTHER BODY PARTS AWAY.

HOT SURFACE HAZARD: DO NOT TOUCH THE PRINT JETS DURING SETUP AND

OPERATION. THE PRINT JETS BECOME VERY HOT.

Caution: Read and follow all instruction prior to setting up the printer.

SHOCK WARNING: DUE TO RISK OF SHOCK, AVOID CONTACT WITH ALL INTERNAL

ELECTRONIC COMPONENTS.
WARNING: THE CUBEPRO SHOULD ONLY BE SERVICED BY AUTHORIZED SERVICE

TECHNICIANS. PRIOR TO ANY PART REPLACEMENT PROCEDURE, THE PRINTER MUST BE

POWERED OFF AND DISCONNECTED FROM UTILITY POWER.

HOT SURFACE HAZARD: WHEN PRINTING WITH ABS MATERIAL, THE INTERIOR (PRINT

CHAMBER) OF THE PRINTER WILL HEAT TO A PREDETERMINED TEMPERATURE. THE

SURFACE OF THE PRINT CHAMBER HEATER WILL BE HOT. AVOID CONTACT WITH THE

PRINT CHAMBER HEATER AND NOTE THAT OTHER COMPONENTS INSIDE THE PRINT

CHAMBER MAY BE HOT.

To ensure safety, please exercise caution when operating your CubePro. Read and follow all safety
precautions as outlined in this user guide. Be careful when operating your CubePro to ensure proper
printing and be mindful of and avoid hot surfaces.

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

Похожие инструкции для CubePro 3D Printer

Бренды по названию

Популярные бренды

3D Systems CubePro 3D Printer, Руководство пользователя

Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

Похожие инструкции для CubePro 3D Printer

Бренды по названию

Популярные бренды