3D Systems CubePro 3D Printer Скачать руководство пользователя страница 27

Страница: 27 / 110

PRINTING YOUR CREATION

There are many 3D creations available at

3dsystems.com/shop/cubepro/downloads

. For more information

about converting a .stl ﬁle into a .cubepro ﬁle which the printer can use, refer to the section titled

CubePro

Software

Printing Procedure

The following steps illustrate how to print a creation.

After powering up your printer and turning on your display, press the touchscreen to begin.

Select PRINT.

NOTE: If the ﬁle is saved on a USB mass storage device, insert the device into the USB

port on the printer.

NOTE: You can also print directly from the CubePro software using a wireless

connection.

Using the arrows, navigate to your ﬁle and select

PRINT

NOTE: The ﬁle name will be displayed at the top.

NOTE: If the print ﬁle requires PLA material and ABS material is installed, the printer

will prompt you to change the cartridge(s). Select

CHANGE CARTRIDGE

and refer to

the section titled

Replacing A Material Cartridge

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 27 / 110

Результаты поиска

Содержание CubePro 3D Printer

Отзывы: