3D Systems CubePro 3D Printer Скачать руководство пользователя страница 28

Страница: 28 / 110

NOTE: If the print ﬁle requires ABS material and PLA material is installed, the printer

will prompt the user to change the cartridge(s). Select

CHANGE CARTRIDGE

and refer

to the section titled

Replacing A Material Cartridge

NOTE: If the print ﬁle requires ABS material but PLA is installed, the printer will

prompt you to change the material cartridge. Select

CANCEL

and follow the

instructions in the section titled

Replacing A Material Cartridge

NOTE: If there is not enough material in the cartridge to complete the print, the

printer will prompt the user to replace the cartridge. Select

CHANGE CARTRIDGE

and

follow the instructions in the section titled

Replacing A Material Cartridge

NOTE: If the creation ﬁle uses color(s) that are not installed, selecting the checkmark

will enable the printer to change the color of the print to a color currently installed.

You can also change the cartridge by selecting

BACK

and following the

CHANGE

CARTRIDGE

instructions. To change the cartridge, refer to the section titled

Replacing

A Material Cartridge

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 28 / 110

Результаты поиска

Содержание CubePro 3D Printer

Отзывы: