manualshive.com logo in svg

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 79 / 110

Поделиться
Скачать
3D Systems CubePro 3D Printer Скачать руководство пользователя страница 79

MAINTENANCE

General Cleaning

Waste material from the printing process can accumulate inside the printer. Using a slightly damp, lint-free
cloth, wipe the interior of the CubePro including the print plate, the print pad, cartridge bays and anywhere
else you might find pieces of plastic waste material.

RISK OF SHOCK: DO NOT WIPE DOWN ANY ELECTRICAL COMPONENTS. ALWAYS KEEP

AWAY FROM ALL AREAS WHERE ELECTRONIC COMPONENTS ARE INSTALLED.

Cleaning The Jet Wiper

In addition to being a scraper for the print jets, the jet wiper assembly is also a refuse bin, collecting print
material that has been primed from the print jets. As the jet wiper fills, it will need to be emptied regularly.

With the print pad lowered, lift the jet wiper off the thumbscrew rest.

1.

Pull the jet wiper up and out to separate the mounting posts from the keyhole slots.

2.

Remove the jet wiper assembly from the printer.

3.

Remove the waste material from the jet wiper and then reinstall it in the CubePro. Refer to the section titled 

Unpacking And Initial Setup

 for more

4.

information about installing the jet wiper. Recycling information can be found in the section titled 

Cubify Sustainability Program

.

Содержание CubePro 3D Printer















































































































Отзывы:

Нет отзывов