manualshive.com logo in svg

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 14 / 110

Поделиться
Скачать
3D Systems CubePro 3D Printer Скачать руководство пользователя страница 14

Unpack the bottom layer of the accessories tray.

9.

NOTE: Depending on the printer configuration, the arrangement of the accessory

boxes may differ. Unpack the print pad (A), the jet wiper assembly (B), and material

cartridges (C). Your configuration may include 1, 2 or 3 cartridges. For configurations

with fewer than three cartridges included, empty boxes may be used as spacers.

CAUTION: The print pad is fragile. Exercise caution when handling the print pad.

Open the front door. Cut away the zip ties (A) and remove the foam tubing from the print jet area.

10.

NOTE: For illustration purposes only, the door was removed from the image. Do not

attempt to remove the door from the printer.

Loosen and remove the four (4) 4mm screws securing the Z-Axis guard and remove the guard. Save the guard and screws for future repacking.

11.

Using a 4mm hex head driver, attach the mounting posts to the jet wiper assembly with the supplied screws and washers.

12.

Содержание CubePro 3D Printer















































































































Отзывы:

Нет отзывов