Zontes ZT350T-D, Maintenance Manual

Page: 67 / 152

67 / 152
Sound, light, and electrical device
Inspection
Caution:
●Before driving, check whether the lights of the whole car
are normal, including turn signals, tail lights, brake lights,
headlights, etc. Whether the horn is normal. Whether the
windshield rises and falls normally.
1. Check
For details of the lamps and lanterns of the whole vehicle,
please refer to the lamps and lanterns distribution diagram in
the vehicle information of this manual.
1. Front brake handle 2. Right handle switch 3. Right auxiliary
switch 4. Meter 5. Left auxiliary switch 6. Left handle switch
7. Rear brake handle
a. Park the vehicle on a flat ground or a lifting platform,
lower the main support, and retract the side support.
b. Press the unlock button of the right auxiliary
switch①After the vehicle is unlocked and energized, confirm
that the flameout switch④ is pulled to " ", pinch the front
or rear brake handle, and press the start button② to start
the engine.
③Light switch: keep it at the "●" position, check whether
the front position light, rear position light and license plate
light are normally on; pull it to " " to check the handle
backlight, front light, front position light, rear position light,
and license plate The lights should all be on.
⑤ECO button: Press the meter and it should light up "E",
and press it again to light up "S", and the two modes can be
switched freely.M125/155 do not have this button.
⑥SEAT: Press to check whether the cushion lock is normally
opened.
⑦FUEL: Press to check whether the fuel tank cover is
normally opened.
c. The left switch button test. If you need a more detailed
understanding of each button function, you can check the
driver's manual. Here is only a brief description of how to test
whether it is normal.
①SET key: Short press SET to enter the main menu/confirm
selection. Long press to return to the main interface. Operate
this button when driving a vehicle is prohibited.
②MOD key: Select the next item. Operate this button when
driving a vehicle is prohibited.
③Windshield switch: Press the windshield glass to complete
from retracting to opening or from opening to retracting.
④Steering switch: Push it to the right to check whether the
front right and rear right turn signals are flashing normally;
press the turn signal to turn off; push it to the left to check
whether the left front and left rear turn signals are normal.
⑤Hazard warning lights: Press it down and the 4 turn signals
will flash, press it again to turn off. It should comply with the
requirements of traffic laws and should not be used in non-
emergency situations.
⑥Horn: Press the horn to sound once to confirm whether
the sound is clear and loud.
⑦Dimmer switch: Pull it to "
" to check whether the high
beam light is on, and the high beam indicator symbol on the
meter lights up at the same time. Pull to "
" to check
whether the low beam light is on. The far and low beams
should be used reasonably in accordance with traffic laws
and regulations.
⑧Overtaking warning light switch: When pressed in the low
beam, it will turn on the high beam.
d. Check the battery voltage
Open the cushion, take off the battery cover and use a
multimeter to measure the battery voltage. If it is lower than
12V, you should use the charger provided with the car to
charge it in time. Be careful not to overcharge and over
discharge, and the charging voltage of the charger must not
be higher than 15V. When the car is not used for a long time,
it should be charged regularly in accordance with the
requirements of the driver's manual. If the battery fails, it
should be properly handled by a professional recycling
agency, and do not discard it at will to avoid environmental
pollution.
If the battery power supply fails to start, it can be charged
through the PKE charging port.
Open the right storage box cover, insert the buckle with
your fingernail or a thin flat-blade screwdriver, press inward
and pull out the buckles on both sides, and then remove the
right storage box cover.