37
887-007_v03
6
Screw the adjusting screw
(6)
into the body
(3)
.
7
Slide the juice channel
(5)
over the adjusting screw until
it snaps on the body
(3)
– “click”.
8
Attach the assembled juicer to the drive unit in the same
way as the mincer body.
9
Insert the adaptor
I
into the bowl
II
. Insert the bowl
(7b)
and the pusher
(8)
– from the mincer unit – onto the
feeding tube.
10
Place the appropriate dishes for the juice and pomace
under the outlet of the juice channel
(5)
and the adjusting
screw
(6)
.
11
Plug in the appliance.
12
Turn the appliance on by means of the switch button
(1a)
, and then feed the fruit, pushing with the pusher.
In order for the juice squeezing process to run
properly do not screw the adjustment screw
too deeply in the initial operation phase. After
assessing the amount of juice in the processed
fruits, adjust the screw in order to obtain an
adequate effectiveness and to avoid clogging
the appliance.
●
Observe the pomace dryness during squeezing. If it
is too dry, unscrew the adjusting screw
(6)
, to avoid
clogging the appliance with the pomace.
The screw adjustment depends on the type of
processed fruits, in case of juicy and ripe fruits
adjust the screw deeper, and for fruits that
are not as juicy, the level of screw adjustment
should be lower.
If the screw adjustment does not provide an
adequate squeezing effectiveness, you can
process the pomace once again.
The clogging of the chamber outlet (in the
adjustment screw (3)) with the pomace of juicy
fruits can cause the flooding of the drive unit.
●
Unplug the appliance if the chamber outlet becomes
clogged. Pay special attention on the juice squeezing
process, make sure the screen openings are not clogged.
Disconnect the juicer from the drive unit (as in the case
of the mincer body), dismantle the juicer, clean (wash)
the juicer elements. Use the included brush to clean the
appliance, especially the screen.
After the work has been finished
●
Turn the meat mincer off and pull the power cord out
from the network supply socket.
1a
Remove the pusher
(8)
and remove the food tray off the
mincing chamber
(2)
or the shredder chamber.
1b
Remove the pusher
(8)
and remove the shredder bowl
with an adaptor
(7b)
off the mincing chamber
(2)
or the
shredder bowl off the shredder chamber.
K
The device with milling cavity and cookies
forming set assembled can operate without any
break not longer than 10 min.
Juicer
The juicer is an accessory for some types of mincers.
It allows squeezing juice from fruits such as: raspberries,
currants, strawberries, gooseberry and additionally from
grapes and tomatoes. Berry fruits such as currants can
be squeezed with stalks. Fruits with large stones, such as
plums, cherries etc. can be squeezed in the appliance after
removing the stones.
Parts of the juicer:
1
Chamber
2
Worm
3
Body
4
Nut
5
Juice channel
6
Adjusting screw
7b
I
Adaptor
II
Shredder bowl
8
Pusher (from the mincer unit)
9
Screen – 2 pieces
No. 1 – smaller openings
No. 2 – larger openings
10
Large sealing ring for the body
(3)
11
Small sealing ring for the worm
(2)
12
Hook
13
Brush
Use only the pusher to push fruits (8).
PREPARING THE JUICER FOR OPERATION
AND ITS OPERATION
1
Make sure that the sealing rings
(10)
and
(11)
are fitted
onto the body
(3)
and the worm
(2)
. If not, insert them into
the sealing grooves in these elements (the body and the
worm).
2
Insert the screen
(9)
into the body
(3)
and press firmly
home.
In order to remove the sieve (9) out of the body
(3), it is helpful to use the hook (12). Put the
shorter end of the hook (12) into the hole of the
sieve (9), and pull the sieve (9) outside.
3
Insert the worm
(2)
into the chamber
(1)
.
4
Insert the body with the screen onto the worm making
sure that the sieve faces downwards , and the positioning
slot fits into the protrusion in the chamber.
5
Screw on the nut
(4)
to attach the body to the chamber
(1)
.
L
M