Zanotti un0 010 Workshop Manual Download Page 142

Page: 142 / 248

131

5.1 Cab Command

Electronics and wiring

Scheduled Maintenance Menu

This menu gives information about required scheduled maintenance procedure and countdown reset for operators after up-
keeping operation.

(zz)

Press

button to slide Menu.

(aaa)

Press

for Programming Menu.

This Menu gives information about required scheduled
maintenance.

(bbb)

After Maintenance procedure press RST to reset

scheduled maintenance countdown (programming
password is required).Otherwise press BACK displaying
home page.

(ccc)

Press SET button to enable password input.

(ddd)

Use

buttons to select 11 (Programming

Password).

(eee)

Press SET button to confirm.

(fff)

Press PROG to execute maintenance countdown reset.

Summary of Contents for un0 010

























































































































































































































































Search results

Summary of Contents for un0 010

Reviews:

Related manuals for un0 010

Brands by name

Popular brands

Zanotti un0 010, Workshop Manual

Search results

Summary of Contents for un0 010

Reviews:

Related manuals for un0 010

Brands by name

Popular brands