YOKOGAWA PX8000 User Manual Download Page 93

Page: 93 / 202

8-2

IM PX8000-02EN

Configuring Detailed Settings of the Waveform Display

(Wave Setup)

Press the

Wave Setup

soft key to display the following screen.

Set the waveform mapping mode (Auto, User).

Set this to turn all waveforms on and off.

When the mapping mode is set to User, you can set how to map each waveform to

the divided screens.

Turns the waveform display on and off

Set the waveform label.

Set the waveform color.

Set the vertical zoom.

For DIV: Set the offset value, waveform’s vertical position,

and magnification.

For SPAN: Set the upper and lower limits of the display range.

These settings are shared between the U menu, I menu,

POWER menu, and AUX menu. ►

chapter 2

When computation mode is OFF: Blank

When computation mode is ON:

When computation is defined: ON or OFF can be selected

When set to OFF: Blank

Depending on the operator set for each computation, the setting

is as follows.

If FFT1 is set to ON, FFT1 appears in the Math7 position.

If FFT2 is set to ON, FFT2 appears in the Math8 position.

Label: Blank

Disp: Blank

Set the FFT waveform color.

Map: -

8.1 Setting the Waveform Display

Summary of Contents for PX8000











































































































































































































Search results

Summary of Contents for PX8000

Reviews:

Related manuals for PX8000

Brands by name

Popular brands

YOKOGAWA PX8000, User Manual

Search results

Summary of Contents for PX8000

Reviews:

Related manuals for PX8000

Brands by name

Popular brands