YOKOGAWA PX8000 User Manual Download Page 174

Page: 174 / 202

23-2

IM PX8000-02EN

Connection Procedure

To Connect to a PC over a Network

Turn off the PX8000.

Connect one end of a UTP (or STP) cable to the ETHERNET 1000BASE-T port on the side
panel.

Connect the other end of the UTP (or STP) cable to a hub or router.

Turn on the PX8000.

PX8000

Hub or router that supports 1000BASE-T

UTP or STP cable

(straight cable)

To Connect to a PC through a Hub or Router

Turn off the PX8000.

Connect one end of a UTP (or STP) cable to the ETHERNET 1000BASE-T port on the side
panel.

Connect the other end of the UTP (or STP) cable to a hub or router.

Connect the PC to the hub or router in the same way.

Turn on the PX8000.

PX8000

Hub or router that supports 1000BASE-T

UTP or STP cable

(straight cable)

Note

• Use a hub or router that conforms to the transfer speed of your network.
• When you connect a PC to the PX8000 through a hub or router, the PC must be equipped with an auto

switching 1000BASE-T/100BASE-TX/10BASE-T network card.

• Do not connect the PX8000 to a PC directly. Direct communication without a hub or router is not

guaranteed to work.

23.1 Connecting the PX8000 to a Network

Summary of Contents for PX8000











































































































































































































Search results

Summary of Contents for PX8000

Reviews:

Related manuals for PX8000

Brands by name

Popular brands

YOKOGAWA PX8000, User Manual

Search results

Summary of Contents for PX8000

Reviews:

Related manuals for PX8000

Brands by name

Popular brands