YOKOGAWA PX8000 User Manual Download Page 37 | Manualshive

Page: 37 / 202

background image

2-20

IM PX8000-02EN

Setting the Rotating Speed Measurement Range

(Vertical Scale, RANGE Knob)

This section explains how to set a fixed range.
(If Auto Range in the AUX menu is set to ON, the measurement range changes depending on the
amplitude of the input signal.)

Turn the

RANGE

knob to set the rotating speed measurement range.

• Auto Range in the AUX menu is set to OFF.
• If the input signal type is analog and you turn the RANGE knob when waveform acquisition is stopped,

two values are shown on the measurement range screen. The upper value is the measurement range
for the displayed waveforms. The lower value is the measurement range that you have specified. The
new range will be applied the next time waveform acquisition is started.

• If you do not operate the RANGE knob for approximately 3 seconds, the measurement range that you

are setting with the knob will disappear from the screen.

Top row: Measurement range for the displayed waveforms

Bottom row: Measurement range that you have specified

Use the RANGE knob to display

the measurement range that is

currently being set.

Measurement Range Options and Units

Below are the available options for the RANGE knob, measurement range values, and

measurement range units that appear on the screen for when the zoom method is set to DIV and
the zoom magnification is set to ×1. If you change the zoom method or zoom magnification, what
appears on the screen will change accordingly.

• When Waveform Acquisition Is Stopped

Input

Signal

Type

Linear

Scaling

Mode

Available Options

for the RANGE Knob

Measurement Range

Values

(that appear on the screen)

Measurement Range Units

(that appear on the screen)

Analog

OFF

50.00mV,

100.0mV,

250.0mV,

500.0mV,

1.000V,

2.500V,

5.000V,

10.00V,

25.00V,

50.00V,

100.0V

Upper value:

RANGE knob value for

the displayed waveform

Lower value:

Available option value of

the RANGE knob

Upper unit value:

Unit selected on the rotating

speed measurement setting

screen

Lower unit value:

Same unit as the available

options for the RANGE knob

AX+B,

P1‒P2

Upper value:

Value obtained by

multiplying the available

option value of the

RANGE knob by the linear

scaling coefficient.

Lower value:

Available option value of

the RANGE knob

Upper unit value:

Unit selected on the rotating

speed measurement setting

screen

Lower unit value:

Same unit as the available

options for the RANGE knob

Pulse

—

1, 2, 5, 10, 20, 50, 100,

200, 500, 1k, 2k, 5k,

10k, 20k, 50k, 100k,

200k, 500k, 1M

Upper value:

No display

Lower value:

Available option value of

the RANGE knob

Upper unit value:

No display

Lower unit value:

Unit selected on the rotating

speed measurement setting

screen

2.5 Configuring Rotating Speed Measurements

«
...
35
36
37
38
39
...
»

Summary of Contents for PX8000











































































































































































































Reviews:

No comments

Related manuals for PX8000

Brand: ABB Pages: 20

Brand: Utilitech Pages: 2

Brand: Kane Pages: 12

Brand: UEi Pages: 8

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Brand: Fender Pages: 20

Dusty Harp Pickup Series

Brand: Dusty Strings Pages: 5

Brand: Magene Pages: 80

Brand: Fluke Calibration Pages: 13

Brand: YOKOGAWA Pages: 14

Brand: Kobold Pages: 44

Brand: Chauvin Arnoux Pages: 44

Brand: Droplet Pages: 35

Brand: Sencore Pages: 75

Brand: truflo Pages: 33

Brand: Proteus Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands