YOKOGAWA PX8000 User Manual Download Page 192

Page: 192 / 202

25-4

IM PX8000-02EN

Execution Errors (650 to 799)

Code

Message

Chapter or

Section

650

Data is invalid.

—

651

The option is not equipped, so it cannot execute.

—

652

Undo is not possible since data that existed immediately before initialization is not available.

—

653

Can not be executed while running.

Press START/STOP key to stop acquisition.

4.2

654

Cannot manipulate files while image printing is in progress.

Wait until image printing is complete.

—

656

Calibration failure.

Disconnect the input and execute again.

If it fails again, servicing is necessary.

24.1

660

Can not operate while data out.

Wait until output is completed.

—

663

Cannot start.

—

664

GO/NO-GO is available while trigger mode is

- ‘Single’ or ‘Normal’

- ‘Auto’ or ‘AutoLevel’ (Faster than 50ms/div)

3.1

666

Failed to measure statistics.

Waveform data may be missing.

If Cycle Statistics is specified, the instrument may be configured in a way that fails to detect the cycle.

14.2, 14.3

667

Executing file access.

Abort or wait until it is complete.

—

668

Image is being printed or saved.

Wait until the execution of the command is complete.

—

672

Cannot be executed when the time base setting is to be an External clock.

4.1

674

Average practice can’t be done because the record length of the history exceeds the record length that

it can be carried out.

20.1

675

Average practice can’t be done because the record length of the history exceeds the record length that

it can be carried out.

20.1

677

Cannot do while selftest is executing.

25.2

679

Cannot start at the current record length. Shorten the record length or meet the following condition.

- Set the trigger mode to Auto, decrease T/Div to less than 100 msec/div to enable roll mode.

- Set the trigger mode to Single or On Start.

2.8, 3.1

680

Averaging mode is not possible when the trigger mode is Single, SingleN, or On Start.

Change the trigger mode.

3.1

684

Cannot start when the time base set to external clock while the acquisition mode set to envelope.

4.1

686

Cannot be executed when the acquisition mode is set to average.

Change the mode.

4.1

693

Cannot be executed when GO/NO-GO mode is Zone.

17.1

695

Set acquisition mode to Normal when using a wave window trigger.

4.1

696

The wave window trigger cannot be used if the sampling rate is faster than 500 kS/s or slower than 10

kS/s.

2.8

702

All search conditions are OFF.

At least one condition should ON.

Chapter 19,

section 20.2

703

Display setting of search source is OFF.

Set it to ON.

8.1

704

Cannot execute Time search while T/div is faster than 100msec/div.

2.8

705

Cannot start Action mode while trigger mode is SingleN.

3.1

706

Cannot be executed when GO/NO-GO mode is ON.

Set the GO/NO-GO mode to OFF.

Chapter 17

707

Cannot execute search while searched No. reached Maximum(1000).

—

708

Cannot execute or set while AutoScroll processing.

Stop AutoScroll.

12.1

712

Cannot start while No GO/NO-GO condition.

Chapter 17

713

Cannot make wave zone from less than 2,000 points data, from more than 10,000,000 points data, or

from less than 10division data.

—

714

Cannot start Action mode while PrintImage target is “File”.

Change target to “printer”.

21.2

716

Set the Math and FFT Window to OFF to Start GO/NO-GO.

Chapter 15,

section 16.1

717

Cannot abort this process.

—

25.1 Messages and Corrective Actions

Summary of Contents for PX8000











































































































































































































Search results

Summary of Contents for PX8000

Reviews:

Related manuals for PX8000

Brands by name

Popular brands

YOKOGAWA PX8000, User Manual

Search results

Summary of Contents for PX8000

Reviews:

Related manuals for PX8000

Brands by name

Popular brands