Yealink Yealink SIP-T26P Page 76 User Manual Download

Page: 76 / 150

User Guide for the SIP-T26P IP Phone

Enter the desired line ID in the Account field or leave it blank.

For more information on the valid values of Account field, refer to

Replace Rule

page

Click Confirm to accept the change.

Note

You can block specific numbers from being dialed on your phone. When you dial a
block out number on your phone, the dialing will fail and the LCD screen will prompt
“Forbidden Number”. You can add 10 block out rules at most on your phone.

To add a block out number via web user interface:

Click on Settings->Dial Plan->Block Out.

Enter the desired value in the BlockOut Number field.

The default values of minimum and maximum length are 1 and 15 respectively.

Area code is configurable via web user interface only.

Summary of Contents for Yealink SIP-T26P























































































































































Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands

Yealink Yealink SIP-T26P, User Manual

Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands