Yealink Yealink SIP-T26P Page 139 User Manual Download

Page: 139 / 150

Troubleshooting

127

Click Confirm to accept the change.

Note

How to make a call using SRTP?

You can enable SRTP to encrypt the audio stream(s) of phone calls. The parties
participating in the call should enable SRTP. You can enable SRTP on a per-line basis.

To enable SRTP via web user interface:

Click

on Account.

Select the desired account from the pull-down list of Account.

Click on Advanced.

Select the desired value from the pull-down list of RTP Encryption (SRTP).

Click Confirm to accept the change.

Note

If logging in the web user interface of the phone with the user credential, you need to
enter the current user password in the Old Password field.

User password is configurable via web user interface only.

SRTP is not available on all servers. Contact your system administrator for more
information.

SRTP is configurable via web user interface only.

Summary of Contents for Yealink SIP-T26P























































































































































Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands

Yealink Yealink SIP-T26P, User Manual

Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands