Yealink Yealink SIP-T26P Page 3 User Manual Download | Manualshive

Page: 3 / 150

background image

Note: This device is tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experience radio/TV technician for help.

To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.

We are striving to improve our documentation quality and we appreciate your feedback. Email
your opinions and comments to

[email protected]

.

«
1
2
3
4
5
...
»

Summary of Contents for Yealink SIP-T26P























































































































































Reviews:

No comments

Related manuals for Yealink SIP-T26P

Galaxy XCover FieldPro

Brand: Samsung Pages: 14

Brand: Samsung Pages: 55

Galaxy Z Flip 5G

Brand: Samsung Pages: 2

Brand: Samsung Pages: 184

Brand: Samsung Pages: 2

Brand: Samsung Pages: 9

Brand: Samsung Pages: 25

Brand: Samsung Pages: 16

Brand: Alcatel Pages: 73

Brand: AU Pages: 30

Brand: qua Pages: 2

Brand: OEM Pages: 25

Brand: Fysic Pages: 60

Brand: Pantech Pages: 261

Brand: Archos Pages: 14

Brand: NEG Pages: 10

Brand: FLY Pages: 33

Brand: UTStarcom Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands