Yealink Yealink SIP-T26P Page 27 User Manual Download

Page: 27 / 150

Getting Started

Press or to select IPv4, IPv6 or IPv4 & IPv6 from the IP Mode field.

Press the Save soft key to accept the change or the Back soft key to cancel.

To configure a static IPv4 address via phone user interface:

Press Menu->Settings->Advanced Settings (password: admin) ->Network->WAN
Port->IPv4->Static IP Client.

Enter the desired values in the IP Address, Subnet Mask, Default Gateway, Pri.DNS
and Sec.DNS fields respectively.

Press the Save soft key to accept the change or the Back soft key to cancel.

To configure a static IPv6 address via phone user interface:

Press Menu->Settings->Advanced Settings (password: admin) ->Network->WAN
Port->IPv6->Static IPv6 Client.

Summary of Contents for Yealink SIP-T26P























































































































































Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands

Yealink Yealink SIP-T26P, User Manual

Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands