manualshive.com logo in svg

Yealink Yealink SIP-T26P, User Manual, Page: 28 / 150

Share
Download
Yealink Yealink SIP-T26P User Manual Download Page 28

User Guide for the SIP-T26P IP Phone 

16

 

2.

 

Enter the desired values in the IPv6, IPv6 Prefix, IPv6 Gateway, IPv6 Pri.DNS and 
IPv6 Sec.DNS fields respectively. 

 

3.

 

Press the Save soft key to accept the change or the Back soft key to cancel. 

If you are using an xDSL modem for IPv4 network connection, you can connect your 
phone to the Internet via PPPoE mode. Set the WAN port as a PPPoE port. The PPPoE port 
will perform a PPP negotiation to obtain the IP address. Contact your system 
administrator for the PPPoE user name and password. 

To configure PPPoE via phone user interface: 

1.

 

Press Menu->Settings->Advanced Settings (password: admin) ->Network->WAN 
Port->IPv4->PPPoE IP Client. 

 

2.

 

Enter the user name and password in the corresponding fields. 

3.

 

Press the Save soft key to accept the change or the Back soft key to cancel. 

Note 

Generally, your phone will be deployed with multiple other phones. In this case, your 
system administrator will configure the phone parameters beforehand, so that after you 
start up your phone, the phone will be registered and ready for use. If your phone is not 
registered, you may have to register it. For more information on how to register your 
phone, refer to 

Account Management

 on page 

58

. 

Wrong network settings may result in inaccessibility of your phone and may also have an 

impact on your network performance. For more information on these parameters, 
contact your system administrator. 

Summary of Contents for Yealink SIP-T26P























































































































































Reviews:

No comments