Yealink Yealink SIP-T26P Page 17 User Manual Download

Page: 17 / 150

Overview

Power Indicator LED

LED Status

Description

Solid green

The phone is initializing.

Fast Flashing green

The phone is ringing (Hardware version must be 4.0.0.2
or higher).

Off

The phone is powered off.
The phone is idle when powered on (Hardware
version must be 4.0.0.2 or higher).

Line key LED

LED Status

Description

Solid green

The line is in conversation.
The line is seized.

Fast flashing green

The line receives an incoming call.

Slow flashing green

The call is placed on hold.

Off

The line is inactive.

Line key LED (configured as BLF key)

LED Status

Description

Solid green

The monitored user is idle.

Fast flashing green

The monitored user receives an incoming call.

Slow flashing green

The monitored user is busy.

Off

The monitored user does not exist.

Memory key LED (configured as BLF key)

LED Status

Description

Solid green

The monitored user is idle.

Flashing red

The monitored user receives an incoming call.

Solid red

The monitored user is busy.

Off

The monitored user does not exist.

Two ways to customize configurations of your SIP-T26P IP phone:



The user interface on the IP phone.



The user interface in a web browser on your PC.

The hardware components keypad and LCD screen constitute the phone user interface,
which allows the user to execute all call operation tasks and basic configuration

Summary of Contents for Yealink SIP-T26P























































































































































Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands

Yealink Yealink SIP-T26P, User Manual

Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands