Yealink Yealink SIP-T26P Page 130 User Manual Download

Page: 130 / 150

User Guide for the SIP-T26P IP Phone

118

To configure voice mail access codes via phone user interface:

Press Menu->Messages->Voice Mail->Set Voice Mail.

Press or to select the account which you want to set, press the 123 soft key
to select the proper input mode and then enter the voice mail access code.

Press the Save soft key to accept the change or the Back soft key to cancel.

Note

To listen to the voice mails:

When the phone user interface prompts receiving new voice mails, press or
the Connect soft key to dial out the voice mail access code.

Follow the voice prompt to listen to voice mails.

Note

To view the voice mail via phone user interface:

Press Menu->Messages->Voice Mail->View Voice Mail.

The LCD screen displays the amount of new and old voice mails.

Select an account and then press the Connect soft key to listen to the voice mails.

Voice mail access code must be predefined on the system server. Contact your
system administrator for the more information.

Before listening to the voice mails, make sure the voice mail access code has been
configured.

When all new voice mails are retrieved, the MESSAGE key LED will go out.

Summary of Contents for Yealink SIP-T26P























































































































































Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands

Yealink Yealink SIP-T26P, User Manual

Search results

Summary of Contents for Yealink SIP-T26P

Reviews:

Related manuals for Yealink SIP-T26P

Brands by name

Popular brands