YASKAWA VIPA System 300S Manual Download Page 54

Page: 54 / 120

Order no.

322-1BH60

Parameter bytes

Diagnostic bytes

Housing

Material

PPE

Mounting

Rail System 300

Mechanical data

Dimensions (WxHxD)

40 mm x 125 mm x 120 mm

Weight

230 g

Environmental conditions

Operating temperature

0 °C to 60 °C

Storage temperature

-25 °C to 70 °C

Certifications

UL certification

yes

KC certification

yes

4.6 322-1BL00 - DO 32xDC 24V 1A

The digital output module collects the binary control signals from the superordinate bus

system and transmits them isolated to the process level. The module has to be provided

with 24V via the front slot. It has 16 channels and their status is monitored via LEDs.

32 outputs, potential separated to the back panel bus

Supply voltage DC 24V

Output voltage 1A per channel

Useable for magnetic valve and DC contactor

LEDs for supply voltage and error messages

Activity LED per channel

Starting from hardware version 4

safe shutdown

is supported.

Chapter 4.1 ‘Safe

shutdown of non-safe outputs’ on page 35

Properties

VIPA System 300S

Digital Output Modules

322-1BL00 - DO 32xDC 24V 1A

HB140 | SM-DIO | | en | Rev. 16-43

Summary of Contents for VIPA System 300S

























































































































Search results

Summary of Contents for VIPA System 300S

Reviews:

Related manuals for VIPA System 300S

Brands by name

Popular brands

YASKAWA VIPA System 300S, Manual

Search results

Summary of Contents for VIPA System 300S

Reviews:

Related manuals for VIPA System 300S

Brands by name

Popular brands