YASKAWA VIPA System 300S Manual Download Page 86

Page: 86 / 120

6.2.1 Fast introduction

For the employment of the I/O modules at the SPEED-Bus the inclusion via the GSD-file

from VIPA in the hardware catalog is required.

To be compatible with the Siemens SIMATIC manager, you have to execute the following

steps:

Start the hardware configurator from Siemens and include the speedbus.gsd for

SPEED7 from VIPA.

Configure the corresponding Siemens CPU.

Starting with slot 4, place the System 300 modules in the plugged sequence.

Project engineering and connection of the SPEED-Bus-CPs res. -DP master at the

standard bus as virtual CP 343-1 (343-1EX11) res. CP 342-5 (342-5DA02 V5.0)

For the SPEED-Bus you always include, connect and parameterize to the

operating

mode

DP master the DP master CP 342-5 (342-5DA02 V5.0) as last module. To

this master system you assign every SPEED-Bus module as VIPA_SPEEDbus

slave. Here the PROFIBUS address corresponds to the slot number beginning with

100 for the CPU. Place at slot 0 of every slave the assigned module and alter the

parameters if needed.

6.2.2 Preconditions

The hardware configurator is part of the Siemens SIMATIC manager. It serves for project

engineering. The modules that may be configured here are listed in the hardware catalog.

For the employment of the System 300S modules at the SPEED-Bus you have to include

the System 300S modules into the hardware catalog via the GSD-file speedbus.gsd from

VIPA.

For the project engineering, a thorough knowledge of the Siemens

SIMATIC manager and the hardware configurator from Siemens is

required!

VIPA System 300S

Digital Modules FAST - SPEED-Bus

Project engineering > Preconditions

HB140 | SM-DIO | | en | Rev. 16-43

Summary of Contents for VIPA System 300S

























































































































Search results

Summary of Contents for VIPA System 300S

Reviews:

Related manuals for VIPA System 300S

Brands by name

Popular brands

YASKAWA VIPA System 300S, Manual

Search results

Summary of Contents for VIPA System 300S

Reviews:

Related manuals for VIPA System 300S

Brands by name

Popular brands