YASKAWA VIPA System 300S Manual Download Page 9

Page: 9 / 120

2.2 Overview

While the standard peripheral modules are plugged-in at the right side of the CPU, the

SPEED-Bus peripheral modules are connected via a SPEED-Bus bus connector at the

left side of the CPU. VIPA delivers profile rails with integrated SPEED-Bus for 2, 6 or 10

SPEED-Bus peripheral modules with different lengths.

The single modules are directly installed on a profile rail and connected via the backplane

bus coupler. Before installing the modules you have to clip the backplane bus coupler to

the module from the backside. The backplane bus couplers are included in the delivery of

the peripheral modules.

With SPEED-Bus the bus connection happens via a SPEED-Bus rail integrated in the

profile rail at the left side of the CPU. Due to the parallel SPEED-Bus not all slots must be

occupied in sequence.

At slot (SLOT 1 DCDC) you may plug either a SPEED-Bus module or an additional power

supply.

You may assemble the System 300 horizontally, vertically or lying.

Please regard the allowed environment temperatures:

horizontal assembly: from 0 to 60°C

vertical assembly: from 0 to 40°C

lying assembly: from 0 to 40°C

2.3 Installation dimensions

1tier width (WxHxD) in mm: 40 x 125 x 120

General

Serial Standard bus

Parallel SPEED-Bus

SLOT 1 for additional

power supply

Assembly possibilities

Dimensions Basic enclo-

sure

VIPA System 300S

Assembly and installation guidelines

Installation dimensions

HB140 | SM-DIO | | en | Rev. 16-43

Summary of Contents for VIPA System 300S

























































































































Search results

Summary of Contents for VIPA System 300S

Reviews:

Related manuals for VIPA System 300S

Brands by name

Popular brands

YASKAWA VIPA System 300S, Manual

Search results

Summary of Contents for VIPA System 300S

Reviews:

Related manuals for VIPA System 300S

Brands by name

Popular brands