YASKAWA VIPA System 300S Manual Download Page 12

Page: 12 / 120

Bolt the profile rail with the background (screw size: M6), so that you still have min-

imum 65mm space above and 40mm below the profile rail. Please look for a low-

impedance connection between profile rail and background.

Connect the profile rail with the protected earth conductor. The minimum cross-sec-
tion of the cable to the protected earth conductor has to be 10mm

Dismantle the according protection flaps of the SPEED-Bus slot with a screw driver

(open and pull down).

For the SPEED-Bus is a parallel bus, not every SPEED-Bus slot must be used in

series. Leave the protection flap installed at an unused SPEED-Bus slot.

At deployment of a DC 24V power supply, install it at the shown position at the pro-

file rail at the left side of the SPEED-Bus and push it to the left to the isolation bolt

of the profile rail.

Fix the power supply by screwing.

Installation of the profile

rail

Installation SPEED-Bus

module

VIPA System 300S

Assembly and installation guidelines

Assembly SPEED-Bus

HB140 | SM-DIO | | en | Rev. 16-43

Summary of Contents for VIPA System 300S

























































































































Search results

Summary of Contents for VIPA System 300S

Reviews:

Related manuals for VIPA System 300S

Brands by name

Popular brands

YASKAWA VIPA System 300S, Manual

Search results

Summary of Contents for VIPA System 300S

Reviews:

Related manuals for VIPA System 300S

Brands by name

Popular brands