Yanmar AW70V Operator'S Manual Download Page 92

Page: 92 / 106

Periodic Inspection

Adjusting the steering system

[Note]

Be sure to install the turning rod to the correct position

(direction).

1. Adjustment of the turning lever neutral position

Adjust the tightening position of the nut (C) so that the

clevis pin (B) loosely moves (with no pressure or

tension applied to the turning rod) when there is no

clearance between the turning link and the stopper pin

(A) (pinching the turning link from the top).

[Note]



Make sure that there is no torsion in the rod when

tightening the nut.



Be sure to lock with the nut.

If the neutral position of the turning lever is not adjusted

correctly, the following problem may occur.

- The response that the operator feels when turning

right and left varies

- Adjustment procedure 3 (Page 93) is not satisfied.

Brake wire 2pc.

Plate length 300mm

Turning rod

Stopper pin

Turning link

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands