Yanmar AW70V Operator'S Manual Download Page 95

Page: 95 / 106

Periodic Inspection

22. Checking and adjusting the
crawler

Jack up the chassis and the lower part of transmission

to adjust the gap between the 4th track roller and the

crawler to 12.5±2.5mm.

<Adjusting>

Jack up the machine on a level ground. The jack

capacity must be over 3 tons. Support the chassis

(pipe) , left and right sides of chassis.

Add a buffer (wood plank) between the jack and

transmission

<Adjusting>

1- Remove the adjust nut stopper.

2- Loosen the lock nuts.

3- Turn the adjusting nut to set the gap.

[Precaution]

Do not tension the crawler too tight (gap below 12.5

2.5mm)

The crawler will be lengthened within a short time if it is

excessively tensioned. As a result, the gap between the

driving sprocket and the crawler will be widened, and

the crawler iron core may be in contact with the driving

sprocket, causing abnormal wear and damage.

Left side of chassis

Right side of chassis

Gap

Tension
bolt

Adjusting
nut

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands