Yanmar AW70V Operator'S Manual Download Page 93

Page: 93 / 106

Periodic Inspection

2. Adjustment of the spool machine bolt located on

the upper side of the actuator

Machine bolt margin E: 17.5±1 mm (both right and left)

[Note]

Be sure to lock with the nut.

If dimension E is not adjusted correctly, the following

problem may occur.

- The response that the operator feels when turning

right and left varies

- Adjustment procedure 3(Page 93) is not satisfied.

3. Adjustment of brake wire

The clearance between the spool on the upper side of

the actuator and the machine bolt while lifting the

machine bolt fixing seat when the turning lever is in the

neutral position.

H: 10±1 mm (both right and left)

If dimension H is insufficient, the following problem may

occur.

- Sudden turning when operating the turning lever

- Excess lever operating force

- Premature wear to the side clutch blade

Lock nut

Machine bolt

Adjusting nut
Lock nut

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands