Yanmar AW70V Operator'S Manual Download Page 37

Page: 37 / 106

Function of parts

Warm-up

Pull the key switch to and remain it in “ON”, this

indicator will be lit. The engine can be started up after

the indicator is off.

Fuel level indicator

This indicator is used to display the fuel level in the fuel

tank.

Tachometer

This meter is used to indicate the speed and Usage

hours of the engine. Do not change the engine speed,

and remain the hand in the green zone during

operation.

Others

Operator’s seat

Move the adjusting pin, and loosen the bolt to adjust

the seat up and down to the position easy for operation.

Engine room cover lock lever

Open the engine room cover with force.

Fuel level indicator

Green zone

Usage hours

Tachometer

Adjusting pin

Adjusting bolt

Lock lever

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands