Yanmar AW70V Operator'S Manual Download Page 79

Page: 79 / 106

Periodic Inspection

6. Cleaning the water separator

Open flame is prohibited during operation.

Be sure to wipe off fuel attached on all
parts. Otherwise, fire hazard may be
caused.

The water separator in the rear part of the machine can

remove dirt and water in fuel.

<Draining>

Dismount the drain bolt shown below to remove water

and dirt.

<Cleaning>

Dismount the water separator to clean the filter element

inside.

Item Interval

Draining

Every 50 hours

Cleaning the filter element

Every 100 hours

Replacing the filter element

Every 200 hours

[IMPORTANT]

The time of cleaning and replacing should be

adjusted as per fuel quality.

7. Draining the fuel tank

Open flame is prohibited during operation.

Be sure to wipe off fuel attached on all
parts. Otherwise, fire hazard may be
caused.

The fuel tank is subject to water and dirt sediment

inside. The sediments may enter the fuel pipeline to

cause problems, thus should be removed regularly.

<Draining>

Take off the drain plug at the bottom of the fuel tank to

remove sediments inside.

Interval

Every 100 hours

Drain

bolt

Fuel port

Drain bolt

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands