Yanmar AW70V Operator'S Manual Download Page 64

Page: 64 / 106

Maintenance after operation

1. Post-operation maintenance



Be sure to stop the engine and lock
the brake pedal before lock cleaning
and unclogging.



Your hand may be nipped by moving
parts or cutter and injuries be caused
in case of maintenance while the
engine is running.



Never smoke or use open fire for
lighting during refueling.



Tighten the fuel tank cover and wipe
off any spilled fuel after refueling.

After cleaning with water, wipe off water fully, and then

add lubricant in various moving and sliding parts. In

particular, the cutters should be coated with lubricating

grease in advance, chains, wires and other greasing

parts must be added with lubricant.

[Precaution]



It is not allowed to clean with water any parts

other than the chassis, so as to avoid failures.



After inspection and maintenance of parts, be

sure to perform test run to check their working

condition.

2. Detaching and opening of each

part

Be sure to stop the engine and lock the
brake pedal before detaching or opening
any parts. Otherwise, you may be injured.

Make sure to replace the detached panels
after operation, or you may get injured.

Opening the threshing section

Open the threshing section as instructed below for

section of the concave screen and inside.

1- Lower down the header to the lowest position, and

then open the upper cover and side cover of the

threshing section.

2- Pull out the pin of rotating fulcrum of the side

threshing section.

3- Pull the fixing lever of threshing section outward to

open the side threshing section.

Upper cover

Fixing lever

Side cover of

threshing chamber

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands