Yanmar AW70V Operator'S Manual Download Page 99

Page: 99 / 106

Trouble shooting

2. Harvesting and conveying section

Condition Check

Remedy

Crops not

conveyed

Cutter blades and conveying chain stuck

by grass, straw, mud, stone or other

foreign matters?

Check the blades and chain, and remove the

foreign matters if any.

Header drive belt loosened?

Adjust the belt

Rice root pulled

out

Crop divider cuts in the root of crop?

Adjust the front end of reel

Too rapid harvesting?

Harvest at a speed suitable to the condition of

crops and field

Cutter blades?

Adjust the gap between cutter blades

Heavy loss in

the reaping

section

Crops accumulated in the front of cutter

blades?

Lower the reel so that crops can flow smoothly

from the cutter blades to the platform auger

Header too high, or the harvested crops

too short?

Lower the header as crops should be

appropriately long to be evenly conveyed to the

platform auger

Reel presses the crops when reverse

harvesting?

Adjust the reel to a proper height

Reel stuck

Angle of reel tines too small?

Adjust the angle of reel tines properly

Reel too low?

Adjust the reel to a proper height

Entry of clay and

stone

Header too low?

Raise the header to a proper height

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands