Yanmar AW70V Operator'S Manual Download Page 100

Page: 100 / 106

Trouble shooting

3. Threshing and screening section

Condition Check

Remedy

Crops not

threshed

completely

Revolving speed of the threshing rotor too

low?

Check the engine tachometer, and adjust the

accelerator lever to raise the engine speed to the

“Green zone”

Chaff discharge adjust lever in the “Open”

position?

Put the lever to “Close” side

Insufficient feed of crops?

Raise the harvesting speed slightly

Crops conveyed unevenly?

Speed up harvesting, and lower the reel

backward if it is too near the front

Grain splashing

Chaff discharge adjust lever in the “Open”

position?

Put the lever to “Close” side

Engine speed too high?

Check the engine tachometer, and adjust the

accelerator lever to raise the engine speed to the

“Green zone”

Angle of the chaff sieve of swing

separator adjusted improperly?

Adjust to an appropriate angle according to the

crop condition

Air volume of fan selected properly?

Adjust correctly

Abnormal sound

in the threshing

section, or

efficiency

decreased

Crops wet out by dew?

Harvest after crops become dry

Revolving speed of the threshing rotor too

low?

Check the engine tachometer, and adjust the

accelerator lever to raise the engine speed to the

“Green zone”

Operating speed too high?

Reduce the existing speed of operation

Chaff discharge adjust lever in the

“Close” position?

Put the lever to “Open” if the moisture content of

rice is high

Crops conveyed unevenly?

Find out the cause of uneven conveying and

remove it.

Poor screening

Angle of the chaff sieve of swing

separator adjusted improperly?

Adjust to an appropriate angle according to the

crop condition

Engine speed too low?

Check the engine tachometer, and adjust the

accelerator lever to raise the engine speed to the

“Green zone”

Air volume of fan, or chaff accumulated at

the air inlet?

Remove the chaff and other obstacles

Air volume of fan selected properly?

Adjust correctly

Lots of

damaged grains

Grain fed properly?

Reduce the harvesting speed in case of abnormal

sound in the threshing section when harvesting

speeds up.

Crops conveyed unevenly?

Find out the cause of uneven conveying and

remove it.

Angle of the chaff sieve of swing

separator adjusted improperly?

Adjust correctly

Lift conveyer pipe attached with mud?

Clean out the mud.

Threshing rotor speed too high?

Check the engine tachometer, and adjust the

accelerator lever to raise the engine speed to the

“Green zone”

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands