Yanmar AW70V Operator'S Manual Download Page 70

Page: 70 / 106

Maintenance after operation

6. Exhaust muffler

Cleaning the front air filter

Dust may accumulate in the pre-cleaner during
operation. Clean it on a daily basis.

Remove the wing nut on top of the pre-cleaner to

remove dust inside.



The pre-cleaner front can not collect all dust.

Clean the air filter while cleaning the pre-cleaner.

[Precaution]



Stop operation and use waterproof cloth to

cover the machine in case of rain during

operation. Pay special attention to the

pre-cleaner to prevent rain.

Pay full attention to prevent air filter from being

caught in the rain in the event that it rains

during transportation.



In case of damage to air filter or inlet pipe,

replace it with a new one. Otherwise, water

may enter and cause engine failure.

Pre-cleaner

Wing nut

https://tractormanualz.com/yanmar/

Summary of Contents for AW70V











































































































Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands

Yanmar AW70V, Operator'S Manual

Search results

Summary of Contents for AW70V

Reviews:

Related manuals for AW70V

Brands by name

Popular brands