8-65
ELECTRICAL COMPONENTS
Starter relay
Starting circuit cut-off relay
Radiator fan motor relay
CHECKING THE TURN SIGNAL RELAY
1. Check:
• Turn signal relay input voltage
Out of specification
→
The wiring circuit from
the main switch to the turn signal relay cou-
pler is faulty and must be repaired.
a. Connect the multimeter to the turn signal
1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe
Result
Continuity
(between “3” to “4”)
1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe
Result
Continuity
(between “3” to “4”)
Br
L B
/
4
L B
/
R W
/
L W
/
1. Positive battery terminal
2. Negative battery terminal
3. Positive tester probe
4. Negative tester probe
Result
Continuity
(between “3” to “4”)
Turn signal relay input voltage
DC 12 V
Multimeter
• Positive tester probe
→
brown “1”
• Negative tester probe
→
ground
R
Br
L
Br W
/
Br
ssssssssssssssssssssssssssss
R
R/W
W/Y
relay terminal as shown.
R/B
8-66
ELECTRICAL COMPONENTS
b. Turn the main switch to “ON”.
c. Measure the turn signal relay input voltage.
2. Check:
• Turn signal relay output voltage
Out of specification
→
Replace.
a. Connect the multimeter to the
turn signal relay terminal as shown.
b. Turn the main switch to “ON”.
c. Measure the turn signal relay output voltage.
CHECKING THE DIODE
1. Check:
• Diode
Out of specification
→
Replace.
NOTE:
The multimeter or the analog multimeter
readings are shown in the following table.
a. Disconnect the diode from the wire harness.
b. Connect the pocket tester (Ω ×1) to the diode
terminals as shown.
c. Check the diode for continuity.
d. Check the diode for no continuity.
CHECKING THE SPARK PLUG CAP
1. Check:
• Spark plug cap resistance
Out of specification
→
Replace.
a. Remove the spark plug cap from the spark
plug lead.
b. Connect the multimeter ( Ω × 1k) to the
spark plug cap as shown.
Turn signal relay output voltage
DC 12 V
Multimeter
• Positive tester probe
→
brown/white “1”
• Negative tester probe
→
ground
Multimeter
Br W
/
Br
1
Continuity
Positive tester probe
→
sky blue
“1”
Negative tester probe
→
red/black “2”
No continuity
Positive tester probe
→
red/black “2”
Negative tester probe
→
sky
blue “1”
Resistance
3.75–6.25 k
Ω
Multimeter
1
2
Sb
R B
/
ssssssssssssssssssssssssssss
ssssssssssssssssssssssssssss
ssssssssssssssssssssssssssss
ssssssssssssssssssssssssssss
ssssssssssssssssssssssssssss
Summary of Contents for YZF-R15
