4-30
4-31
REAR BRAKE
REAR BRAKE
INTRODUCTION
WARNING
1. Remove:
• Rear wheel
Refer to “REAR WHEEL” on page 4-12.
2. Check:
• Brake disc
Damage/galling
→
Replace.
3. Measure:
• Brake disc deflection
Out of specification
→
Correct the brake disc
deflection or replace the brake disc.
Refer to “CHECKING THE FRONT BRAKE
DISC” on page 4-18.
4. Measure:
• Brake disc thickness
Measure the brake disc thickness at a few dif-
ferent locations.
Out of specification
→
Replace.
Refer to “CHECKING THE FRONT BRAKE
DISC” on page 4-18.
5. Adjust:
• Brake disc deflection
Refer to “CHECKING THE FRONT BRAKE
DISC” on page 4-18.
6. Install:
• Rear wheel
Refer to “REAR WHEEL” on page 4-12.
REPLACING THE REAR BRAKE PADS
When replacing the brake pads, it is not neces-
sary to disconnect the brake hose or disassem-
ble the brake caliper.
1. Remove:
• Brake pads
• Brake pad spring
To remove the inner brake pad “1”, push down
on the brake caliper bracket so that there is
space to remove the brake pad.
2. Measure:
• Brake pad wear limit “a”
Out of specification
→
Replace the brake
pads as a set.
Brake disc deflection limit
0.10 mm
Brake disc thickness limit
4.0 mm
Rear brake disc bolt
LOCTITE
3. Install:
• Brake pad spring
• Brake pads
NOTE:
Always install new brake pads and a new brake
pad spring as a set.
a. Connect a clear plastic hose tightly to the
bleed screw. Put the other end of the hose
into an open container.
b. Loosen the bleed screw and push the brake
caliper piston into the brake caliper with your
finger.
c. Tighten the bleed screw.
d. Install a new brake pad spring “1” and new
brake pads.
NOTE:
Install the brake pad spring as shown.
4. Install:
• Brake pad retaining bolts
• Brake caliper
5. Install:
• Rear wheel
Refer to “REAR WHEEL” on page 4-12.
6. Check:
• Brake fluid level
Below the minimum level mark “a”
→
Add the
recommended brake fluid to the proper level.
Refer to “CHECKING THE BRAKE FLUID
LEVEL” on page 3-19.
7. Check:
• Brake pedal operation
Soft or spongy feeling
→
Bleed the brake sys-
tem.
Refer to “BLEEDING THE HYDRAULIC
BRAKE SYSTEM” on page 3-19.
REMOVING THE REAR BRAKE CALIPER
NOTE:
Before disassembling the brake caliper, drain
the brake fluid from the entire brake system.
Brake pad lining thickness (in-
ner)
7.0 mm
Limit
1.5 mm
Brake pad lining thickness (out-
er)
7.0 mm
Limit
1.5 mm
T
R
.
.
Rear brake caliper bleed screw
6 Nm (0.6 m · kg, 4.2ft· lb)
New
New
T
R
.
.
Rear brake pad retaining bolt
18 Nm (1.8 m·kg, 13 ft·lb)
LOCTITE®
1
a
sssssssssssssssssssssssssssssssssssssss
sssssssssssssssssssssssssssssssssssssss
sssssssssssssssssssssssssssssssssssssss
sssssssssssssssssssssssssssssssssssssss
Summary of Contents for YZF-R15
