![background image](http://html.mh-extra.com/html/yamaha/motif-rack-es/motif-rack-es_owners-manual_902713098.webp)
Owner’s Manual
MIDI Data Format
98
Appendix
(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)
All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain or
Sostenuto is on, notes will continue sounding until these are turned off.
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF.
Sets VOICE RECEIVE CHANNEL to “OMNI OFF,” channel 1.
(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF.
Sets VOICE RECEIVE CHANNEL to “OMNI ON.”
(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0..16)
Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16, the
channel will be Mode 4 (m = 1).
In the Voice mode, the mode can be Mode 2 (m = 1) according to VOICE RECEIVE CHANNEL.
(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode3.
In the Voice mode, the mode can be Mode 1 according to VOICE RECEIVE CHANNEL.
(3-3) REGISTERED PARAMETER NUMBER
STATUS
1011nnnn(BnH)
n = 0 - 15 CHANNEL NUMBER
LSB
01100100(64H)
RPN LSB
0ppppppp
p = RPN LSB (Refer to the table as shown below.)
MSB
01100101(65H)
RPN MSB
0qqqqqqq
q = RPN MSB (Refer to the table as shown below.)
DATA ENTRY MSB
00000110(06H)
DATA VALUE
0mmmmmmm
m = Data Value
DATA ENTRY LSB
00100110(26H)
DATA VALUE
0lllllll
l = Data Value
First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.
RPN D.ENTRY
LSB MSB MSB LSB
PARAMETER NAME
00H 00H mmH ---
PITCH BEND SENSITIVITY
01H 00H mmH llH
MASTER FINE TUNE
{mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}
(-8192*100/8192) - 0 - (+8192*100/8192)
02H 00H mmH ---
MASTER COARSE TUNE
28H - 40H - 58H (-24 - 0 - +24 semitones)
7FH 7FH --- ---
RPN RESET
RPN numbers will be left not designated.
The internal values are not affected.
(3-4) NON-REGISTERED PARAMETER NUMBER
There are no applicable parameters.
These are transmitted to the Plug-in Board.
(3-5) SYSTEM REAL TIME MESSAGES
(3-5-1) ACTIVE SENSING
STATUS
11111110(FEH)
Once this code is received, the instrument starts sensing. When neither status nor data is received for over
approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the sustain switch
are forcibly turned off. In this case, each control data will be reset to a certain value.
(3-6) SYSTEM EXCLUSIVE MESSAGE
(3-6-1) UNIVERSAL NON REALTIME MESSAGE
(3-6-1-1) GENERAL MIDI MODE ON
F0H 7EH 7FH 09H 01H F7H
The PLG100-XG Plug-in Board installed to the instrument will receive this message when the instrument
is in the Multi mode and SYSTEM Receive GM/XG is set to on.
The internal Part values will be reset according to the SYSTEM when the Port is set to 1.
(3-6-1-2) IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H
(“n” = Device No. However, this instrument receives under “omni.”)
(3-6-1-3) IDENTITY REPLY (Transmit only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H
dd; Device Number Code
MOTIF-RACK ES: 19 06
(3-6-2) UNIVERSAL REALTIME MESSAGE
(3-6-2-1) MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Sets the MASTER VOLUME value.
The value “mm” is used to set the master volume (the value “ll” should be ignored).
(3-6-3) PARAMETER CHANGE
(3-6-3-1) XG SYSTEM ON
11110000
F0
Exclusive Status
01000011
43
YAMAHA ID
0001nnnn
1n
Device Number
01001100
4C
Model ID
0aaaaaaa
0
Address High
0aaaaaaa
0
Address Mid
0aaaaaaa
7E
Address Low
0
0
Data
11110111
F7
End of Exclusive
In MULTI MODE, received only when the PLG100-XG is installed and SYSTEM Receive GM/XG on is set
to on.
Be aware that executing this message takes about 170 ms and that, therefore, a certain interval before
executing the following message is needed.
(3-6-3-2) NATIVE PARAMETER CHANGE, MODE CHANGE
11110000
F0
Exclusive Status
01000011
43
YAMAHA ID
0001nnnn
1n
Device Number
01111111
7F
Model ID
00000000
00
Model ID
0aaaaaaa
aaaaaaa
Address High
0aaaaaaa
aaaaaaa
Address Mid
0aaaaaaa
aaaaaaa
Address Low
0ddddddd
ddddddd
Data
|
|
11110111
F7
End of Exclusive
For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
For Address, see the MIDI Data Table in the separate Data List.
(3-6-4) BULK DUMP
11110000
F0
Exclusive Status
01000011
43
YAMAHA ID
0000nnnn
0n
Device Number
01111111
7F
Model ID
00000000
00
Model ID
0bbbbbbb
bbbbbbb
Byte Count
0bbbbbbb
bbbbbbb
Byte Count
0aaaaaaa
aaaaaaa
Address High
0aaaaaaa
aaaaaaa
Address Mid
0aaaaaaa
aaaaaaa
Address Low
0
0
Data
|
|
0ccccccc
ccccccc
Check-sum
11110111
F7
End of Exclusive
For Address and Byte Count, see the MIDI Data Table in the separate Data List.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data
and Check sum itself are added.
(3-6-5) DUMP REQUEST
11110000
F0
Exclusive Status
01000011
43
YAMAHA ID
0010nnnn
2n
Device Number
01111111
7F
Model ID
00000000
00
Model ID
0aaaaaaa
aaaaaaa
Address High
0aaaaaaa
aaaaaaa
Address Mid
0aaaaaaa
aaaaaaa
Address Low
11110111
F7
End of Exclusive
For Address and Byte Count, see the MIDI Data Table in the separate Data List.
(3-6-6) PARAMETER REQUEST
11110000
F0
Exclusive Status
01000011
43
YAMAHA ID
0011nnnn
3n
Device Number
01111111
7F
Model ID
00000000
00
Model ID
0aaaaaaa
aaaaaaa
Address High
0aaaaaaa
aaaaaaa
Address Mid
0aaaaaaa
aaaaaaa
Address Low
11110111
F7
End of Exclusive
For Address, see the MIDI Data Table in the separate Data List.