![background image](http://html.mh-extra.com/html/yamaha/motif-rack-es/motif-rack-es_owners-manual_902713090.webp)
Owner’s Manual
Utility
90
CtrlReset
Controller Reset
Determines the status of the external controllers when switching between Voices. When this is set to “off,”
the controllers are kept at the current setting. When this is set to “on,” the controllers are reset to the default
states (below).
Settings:
reset, hold
If you select “reset,” the controllers will be reset to the following states/positions:
Pitch Bend: Center
Foot Switch: Off
Modulation Wheel: Minimum
Expression: Maximum
Aftertouch: Minimum
Foot Volume: Maximum
Foot Controller: Maximum
Sustain: Off
Breath Controller: Maximum
LCD Cntrst
LCD Contrast
Sets the LCD display for optimum legibility.
Settings:
1~16
PlgAutoLoad
Plug-in Auto Load
Determines whether the Board Voice data is automatically loaded (on) or not (off) when turning the power on
(Plug-in Load function in the JobSel display).
Settings:
On, Off
BulkIntrval
Bulk Interval
Determines the transmit interval of the Bulk Dump.
Settings:
1~5
The higher the value, the larger the transmit interval.
Output
L&R Gain
L Gain and R Gain
Sets the signal gain of each output jack.
Settings:
0dB, +6dB
Asn1/2Gain
Assignable 1/2 Gain
Asn3/4Gain
Assignable 3/4 Gain
MEQ (Master Equalizer)
These special voice-related settings are available only when entering the Utility from the Voice mode, From
this display you can apply five-band equalization (LOW, LOW MID, MID, HIGH MID, HIGH) to all Voices.
Parameters are the same as in the MEQ display in the Performance/Multi Common Edit mode (page 79).
n
For details about Equalizer, see page 60.
MEF (Master Effect)
These special voice-related settings are available only when entering the Utility from the Voice mode. From
this display you can set the Master Effect related parameters applied to all the Voices. Parameters are the
same as in the MEF display in the Performance/Multi Common Edit mode (page 80).
Voice
These special voice-related settings are available only when entering the Utility from the Voice mode. From
this display you can make settings that apply commonly to all Voices.
ArpOutSw
Arpeggio Output Switch
This enables or disables MIDI data output for the Arpeggio function. When this is set to “on,” Arpeggio data
is sent via MIDI in the Voice mode. In the Performance/Multi mode, you can set in the “OutputSw” parameter
from the Arpeggio Edit.
Settings:
on, off
ArpTransCh
Arpeggio Transmit Channel
Determines the MIDI channel through which Arpeggio playback data will be sent (when Output Switch
above is on). In the Performance/Multi mode, you can set this in the “TransmitCh” parameter in the Arpeggio
Edit mode (page 89).
Settings:
1~16
AS1/2 Assign
Assign 1/2
Sets the parameters related to the controllers in the Voice mode. Parameters are the same as in the CtrlAsn
display in the Performance/Multi Common Edit mode (page 80).
BC Assign
Breath Controller
RB Assign
Ribbon Controller
FC1/2 Assign
Foot Controller
CtrlAsn (Control Assign)
Determines the Control Numbers corresponding to the external controllers. For details, see page 46.
ArpSwitch
Arpeggio Switch
Determines the Control Number that controls on/off for Arpeggio playback.
Settings:
off, 1~95
ArpHold
Arpeggio Hold
Determines the Control Number that controls on/off for the “Hold” parameter (page 88).
ASA/B Asgn
Assign A/B
Determines the Control Numbers corresponding to Assign A and Assign B, and sets the Destinations
(functions) assigned to the Control Numbers.
Settings:
Refer to the separate Data List booklet.
ASA/B Dest
Assign A/B Destination
FS Asgn
Foot Switch Assign
Determines the Control Number corresponding to the Footswitch.
Settings:
Refer to the separate Data List booklet.
ArpAsgn
Arpeggio Assign
Determines the Control Number for switching among Arpeggios 1-5, stored to each Voice/Performance/
Multi. For details, see page 44.
ArpAsgnMode
Arpeggio Assign Mode
Determines the mode for switching among Arpeggios 1-5, stored to each Voice/Performance/Multi.
Settings:
inc, direct
inc.................... Each time the MOTIF-RACK ES receives a message via the selected Control Change number, Arpeggios 1-5
can be switched. The actual Control Change data value does not matter.
direct ............... You can select the Arpeggio corresponding to the value of the selected Control Change number: 0~25
(Arpeggio 1), 26~50 (Arpeggio 2), 51~76 (Arpeggio 3), 77~101 (Arpeggio 4), 102~127 (Arpeggio 5)
Utility
V
oice mode
P
erf
or
mance mode
Multi mode
Eff
ect
Ar
peggio
Ref
erence