manualshive.com logo in svg

Yamaha MM600D, Manual

The Yamaha MM600D Service Manual is a comprehensive user manual for your MM600D model, containing detailed instructions, diagrams, and troubleshooting techniques. Easily accessible for free download at manualshive.com, this manual ensures you have all the information you need to maximize the performance of your Yamaha MM600D.

Share
Download
background image

30 

CHAPTER ONE 

ever, because snowmobiles are often operated in extreme 
weather conditions, over rough terrain, and in remote ar- 
eas, they should be checked before each ride and main- 

tained on a periodic basis. 

WARNING

Never lean into a snowmobile 

's

engine com- 

partment  while 

wearing  a  scarf  or  other 

loose clothing when the engine is running or 
when the driver is starting the engine. I f  the 
scarf or clothing should catch  in the drive 
belt or clutch, severe injury or death could 

result. 

Prestart Inspection 

Always  perform a  prestart inspection before heading 

out on a snowmobile. While the following list may look 
exhaustive, it  can  be  performed  rather quickly after be- 
coming familiar with it. 
1. 

Familiarize yourself with the snowmobile. 

2.  Clean the windshield with a clean, damp cloth. Do not 

use gasoline, solvents or abrasive cleaners. 
3. 

Check track tension (Chapter Three) and adjust if nec- 

essary. 
4.  Check  the  tether  switch  and  the  emergency  cut-out 
switch for proper operation. If your machine is new or if 
you are using a friend's machine, practice using the tether 
or stop switch a few times so its use will be automatic dur- 
ing an emergency. 

5. 

Check the brake operation. Make sure the brake sys- 

tem is correctly adjusted and operates properly, 

6. 

Check the fuel level and fill as needed. 

7.  Check the injection oil tank. Make sure it is full. 
8.  Check the coolant level. 
9.  Operate  the  throttle  lever.  It  should  open  and  close 
smoothly. 

10.  Open  the belt  guard and  visually inspect the  drive 
belt. If the belt seems worn or damaged, replace it. Chap- 

ter  Fourteen  lists  drive  belt  wear  limit  specifications. 
Close the belt guard after inspecting the belt. Make sure 
the belt guard mounts are not loose or damaged. 
11.  While the engine shroud is open, visually inspect all 
hoses, fittings and parts for looseness or damage. Cheek 
the tightness of all bolts and nuts. Tighten as required. 
12.  Check  the  handlebar  and  steering  components  for 
looseness or damage. Do not ride the vehicle if any steer- 
ing component is damaged. Tighten loose fasteners as re- 
quired. 
13. 

After  closing  the  shroud,  make  sure  the  shroud 

latches are fastened securely. 

14.  Check the skis for proper alignment (Chapter Three). 
Check the ski pivot bolt for tightness or damage. 

WARNING 

When starting the engine, make sure no by- 
standers are in front or behind the snowmo- 
bile. A  sudden lurch of the machine could 
cause serious 

injury. 

15.  Make sure all lights are working. 

NOTE 

I f  

abnormal noises are heard after starting 

the engine, repair the problem  before start- 
ing out. 

NOTE 

Refer to the appropriate chapter for torque 
specifications and service procedures. 

Tool Kit 

Before leaving on a  trip, make sure to  take tools and 

spare parts in case of an emergency. A tool kit should in- 
clude the following: 

1. 

Flashlight. 

2.  Rope. 

3.  Tools. 
4.  Tape. 

Spare Parts 

A spare parts kit should include the following: 

1. 

Drive belt. 

2. 

Emergency starter rope. 

3, 

Light bulbs. 

4. 

Spark plugs. 

5.  Main jets. 

6.  Throttle cable. 
7.  Brake cable. 
8. 

This book 

. . . 

just in case. 

Take extra oil and fuel if going on 

a long trip. 

Emergency Starting 

If the recoil starter rope should break (and the electric 

starter does not work), start the engine with an emergency 
rope that is wrapped around the primary sheave cap. 

WARNING 

The 

drive belt guard must be removed when 

starting  the  engine  with  the  emergency 
starter rope. Never lean into a snowmobile 

's

engine compartment while wearing a scarf 

Summary of Contents for MM600D



























































































































































































































































































Reviews:

No comments

Related manuals for MM600D

Hamron 008041 Operating Instructions Manual preview
008041
Brand: Hamron Pages: 12
Land Pride Treker 4200ST Parts Manual preview
Treker 4200ST
Brand: Land Pride Pages: 132
Land Pride Gondo 4400EX Operator'S Manual preview
Gondo 4400EX
Brand: Land Pride Pages: 50
Suzuki kq750 2008 Service Manual preview
kq750 2008
Brand: Suzuki Pages: 576
Suzuki LT-A450X 2006 Owner'S Manual preview
LT-A450X 2006
Brand: Suzuki Pages: 139
Ski-Doo Tundra Series Operator'S Manual preview
Tundra Series
Brand: Ski-Doo Pages: 159
Ski-Doo 2006 Mini Z Operator'S Manual preview
2006 Mini Z
Brand: Ski-Doo Pages: 103
TGB EST 1000 Service Manual preview
EST 1000
Brand: TGB Pages: 269
TGB BLADE 500 Service Manual preview
BLADE 500
Brand: TGB Pages: 306
Can-Am Renegade 500 Operator'S Manual preview
Renegade 500
Brand: Can-Am Pages: 144
Ultra-tow 49802 Owner'S Manual preview
49802
Brand: Ultra-tow Pages: 8
Arctic Cat 2012 700 i Cruiser Operator'S Manual preview
2012 700 i Cruiser
Brand: Arctic Cat Pages: 708
Parklands 700ATV Maintenance Manual preview
700ATV
Brand: Parklands Pages: 101
Arctic Cat 2012 ATV 150 Operator'S Manual preview
2012 ATV 150
Brand: Arctic Cat Pages: 64
Arctic Cat 2012 90 Utility Service Manual preview
2012 90 Utility
Brand: Arctic Cat Pages: 83
Yamaha YFM250RX 2008 Service Manual preview
YFM250RX 2008
Brand: Yamaha Pages: 311
Yamaha SRX600C Owner'S Manual preview
SRX600C
Brand: Yamaha Pages: 81
Yamaha Phazer PZ50Y Owner'S Manual preview
Phazer PZ50Y
Brand: Yamaha Pages: 98

Brands by name

Popular brands

Load more brands