Yamaha MM600D Manual Download | Manualshive

Page: 193 / 282

background image

set, alignment and parallelism. Different alignment bars
are used for the various models. Check with a
dealership for the availability of the correct alignment bar
for

appropriate model.

WARNING

Never lean into the snowmobile's engine

compartment while wearing a

other

loose clothing when the engine is running or
when starting the engine. I f the scurf or
clothing should catch in the drive

belt or

clutch, severe injury

or

death could occur.

1.

Open the hood.

2.

Remove the cover from the primary sheave, belt and

secondary sheave.

3.

Check the drive belt for the manufacturer's marks so

that during installation it will

run

in the correct direction.

If the belt is not marked, draw an arrow on the belt facing
forward or install a new belt.

4. Push against the secondary sheave (Figure 7), rotating
it clockwise to separate the sheave halves. Then roll the

over the secondary sheave and remove it.

5.

Inspect the drive belt as described in this chapter.

6.

Perform the drive belt alignment procedure as de-

scribed in this chapter.
7.

Reverse Steps 1-4 and install the drive belt. If install-

ing the original belt, be sure to install it so the manufac-
turer's marks on the belt (or those made before removal)
face in the same direction (forward). When installing a
new belt, install it so the belt identification marks are visi-
ble while standing on the left side of the machine looking
into the engine compartment.

Inspection

Check the drive belt frequently and at least once each

season remove the belt and carefully inspect it.
1.

Remove the drive belt as described in this chapter.

2.

Measure the width of the drive belt at its widest point

(Figure 8). Replace the belt

if

the width is

than the

minimum listed in Table 2.

Measure the circumference of the drive belt with a tape

measure (Figure

9). Replace the belt if the outside cir-

cumference is not within the limits listed in Table

2.

4.

Inspect the belt as follows:

a. Check the sides of the belt for a frayed edge cord

(Figure

10). This indicates drive belt misalignment.

Drive belt misalignment can be caused by incorrect
sheave alignment and loose engine mounting bolts.
Examine the belt for a section that is worn narrower
in one section (Figure

11) than the rest of the belt.

This condition is caused by excessive belt slippage
because of a stuck track or to abnormally high en-
gine idle speed.

Check for drive belt disintegration (Figure 12)
caused by excessive belt wear or misalignment.
Disintegration can also be caused by the use of an
incorrect belt.

«
...
191
192
193
194
195
...
»

Summary of Contents for MM600D



























































































































































































































































































Reviews:

No comments

Related manuals for MM600D

Brand: Linhai Pages: 208

Brand: E-TON Pages: 134

Brand: KYMCO Pages: 89

WILD HP 300 - SERVICE

Brand: GAS GAS Pages: 65

Brand: wsm Pages: 25

Brand: Hisun Pages: 116

Brand: Satellite Suites Pages: 39

Ranger 500 2x4 2007

Brand: Polaris Pages: 345

Brand: E-Z-GO Pages: 80

Express L4 - Gas

Brand: E-Z-GO Pages: 86

Brand: Baja motorsports Pages: 10

Brand: ShoreLand'r Pages: 10

Brand: Tracker Off-Road Pages: 68

Brand: Tracker Pages: 156

Brand: Sym Pages: 100

Quad Lander 300

Brand: Sym Pages: 244

Sportsman XP Touring 1000

Brand: Polaris Pages: 121

Brand: Polaris Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands