manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 4

Table of contents

General information .......................... 1

Identification numbers record ..........  1

Outboard motor serial number ...........  1
Key number ........................................  1

Emission control information ...........  1

North American models......................  1
Star labels ..........................................  2

Safety information ...........................  3
Important labels...............................  4

Warning labels....................................  4

Basic boating rules 

(Rules of the road) .......................  5

Steering and sailing rules and sound 

signals.............................................  5

Rules when encountering vessels......  5
Other special situations ......................  6

Fueling instructions .........................  8

Gasoline .............................................  9
Engine oil............................................  9

Battery requirement.......................  10

Battery specifications .......................  10

Propeller selection.........................  10
Start-in-gear protection .................  11

Basic components .......................... 12

Main components..........................  12

Remote control .................................  13
Remote control lever ........................  14
Free accelerator ...............................  14
Throttle friction adjuster....................  15
Engine stop lanyard switch...............  15
Main switch.......................................  16
Power trim and tilt switch on remote 

control or tiller handle....................  16

Power trim and tilt switch on bottom 

engine cowling ..............................  17

Power trim and tilt switches 

(twin binnacle type) .......................  17

Trim tab with anode..........................  17
Tilt support lever for power trim and 

tilt or hydro tilt model.....................  18

Top cowling lock lever 

(pull up type) .................................  19

Flushing device ................................  19
Water separator................................  19
Digital tachometer ............................  20
Low oil pressure warning indicator ...  20
Overheat warning indicator 

(digital type) ..................................  20

Speedometer (digital type) ...............  21
Trim meter (digital type) ...................  21
Hour meter (digital type) ...................  22
Trip meter .........................................  22
Clock ................................................  22
Fuel gauge .......................................  23
Fuel warning indicator ......................  23
Low battery voltage warning 

indicator ........................................  23

Fuel management meter ..................  24
Fuel flow meter .................................  24
Fuel consumption meter ...................  25
Fuel economy ...................................  25
Twin-engine speed synchronizer......  26
Water separator warning indicator ...  26
Command link multifunction 

meters ...........................................  26

Tachometer unit ...............................  27
Speed & fuel meter unit ....................  30
Speedometer unit .............................  31
Fuel management meter ..................  32

Warning system ............................  32

Overheat warning (twin engines)......  32
Low oil pressure warning..................  33

Operation ......................................... 34

Installation.....................................  34

Mounting the outboard motor ...........  34

Breaking in engine ........................  35

Procedure for 4-stroke models .........  35

Preoperation checks .....................  35

Fuel ..................................................  36
Controls ............................................  36
Stop switches ...................................  36
Engine ..............................................  36
Checking the engine oil level............  36

Filling fuel......................................  36

Ring Free Fuel Additive ....................  36

U6P213E0.book  Page 1  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands