manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 72

Maintenance

66

2.

Always keep the battery in a good state of
charge. Installing a voltmeter will help
you monitor your battery. If you will not
use the boat for a month or more, remove
the battery from the boat and store it in a
cool, dark place. Completely recharge
the battery before using it.

3.

If the battery will be stored for longer than
a month, check the specific gravity of the
fluid at least once a month and recharge
the battery when it is low.

NOTE:

Consult a Yamaha dealer when charging or
re-charging batteries.

EMU30730

Connecting the battery

WARNING

EWM00570

Mount the battery holder securely in a dry,
well-ventilated, vibration-free location in
the boat. Install a fully charged battery in
the holder.

CAUTION:

ECM01500

●

Make sure the main switch (on applica-
ble models) is “

” (off) before working

on the battery.

●

Reversal of the battery cables will dam-
age the electrical parts.

●

If you connect the battery cables in the
reverse order, consult a Yamaha dealer
immediately.

●

Connect the red battery cable first when
installing the battery and disconnect the
black battery cable first when removing
it. Otherwise, the electrical parts can will
be damaged.

●

The electrical contacts of the battery
and cables must be clean and properly
connected, or the battery will not start
the engine.

Connect the RED battery cable to the POSI-
TIVE (+) terminal first. Then connect the
BLACK battery cable to the NEGATIVE (-) ter-
minal.

Connecting an accessory battery (optional)
1.

Remove the accessory battery coupler
cover from the outboard motor.

2.

Connect the accessory battery coupler to
the coupler of the accessory battery ca-
ble (optional). Use a connecting cable be-
tween the (-) terminals of the starting
battery and accessory battery. See the il-
lustrations of the wiring connections. This
cable must be made from wire thicker
than the starting battery cable.

WARNING

EWM00600

Use of smaller wire could lead to a fire.

1. Red cable

2. Black cable
3. Battery

U6P213E0.book  Page 66  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands