manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 55

Maintenance

49

EMU28303

Procedure

EMU31920

Conditioning and stabilizing fuel

Fill the fuel tank with fresh fuel and add one
ounce of “Yamaha Fuel Conditioner and Sta-
bilizer” (Part No. LUB-FUELC-12-00) to each
gallon of fuel.

NOTE:

The use of “Yamaha Fuel Conditioner and
Stabilizer” eliminates the need to drain the
fuel system. Consult your Yamaha dealer or
other qualified mechanic if the fuel system is
to be drained instead.

EMU31900

Engine anti-rust measure

CAUTION:

ECM01530

Do not perform this procedure while the
engine is running. The water pump may be
damaged and severe damage from over-
heating can result.

NOTE:

This procedure is performed while the top
cowling is removed.

1.

Remove the spark plug(s).

2.

Pour a teaspoonful of clean engine oil
into each cylinder.

3.

Crank the engine several times manually.

4.

Reinstall the spark plug(s).

EMU31390

Washing the outboard motor

NOTE:

This procedure is performed while the top
cowling is installed.

1.

Wash the outboard motor body using
fresh water.

2.

Drain the cooling water completely out of
the motor. Clean the body thoroughly.

EMU28401

Lubrication

1.

Grease the spark plug threads and install
the spark plug(s) and torque to proper
specification. For information on spark
plug installation, see page 54.

2.

Change the gear oil. For instructions, see
page 63. Inspect the oil for the presence
of water that indicates a leaky seal. Seal
replacement should be performed by an
authorized Yamaha dealer prior to use.

3.

Grease all grease fittings. For further de-
tails, see page 54.

EMU28421

Cleaning and anticorrosion measures

1.

Wash down the exterior of the outboard
motor with fresh water and dry off com-
pletely.

2.

Spray the outboard motor exterior with
“Yamaha Silicone Protectant” (Part No.
LUB-SILCNE-13-00).

3.

Wax the cowling with a non-abrasive wax
such as “Yamaha Silicone Wax” (Part No.
ACC-11000-15-02).

EMU28430

Battery care

WARNING

EWM00330

Battery electrolytic fluid is dangerous; it
contains sulfuric acid and therefore is poi-
sonous and highly caustic.
Always follow these preventive measures:

ZMU04261

U6P213E0.book  Page 49  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands