manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 7

General information

1

EMU25170

Identification numbers record

EMU25183

Outboard motor serial number

The outboard motor serial number is stamped
on the label attached to the port side of the
clamp bracket.
Record your outboard motor serial number in
the spaces provided to assist you in ordering
spare parts from your Yamaha dealer or for
reference in case your outboard motor is sto-
len.

EMU25190

Key number

If a main key switch is equipped with the mo-
tor, the key identification number is stamped
on your key as shown in the illustration.
Record this number in the space provided for
reference in case you need a new key.

EMU25221

Emission control information

EMU25230

North American models

This engine conforms to U.S. Environmental
Protection Agency (EPA) regulations for ma-
rine SI engines. See the label affixed to your
engine for details.

EMU31560

Approval label of emission control certifi-
cate

This label is attached to the bottom cowling.
New Technology; (4-stroke) MFI

1. Outboard motor serial number location

1. Key number

1. Approval label location

U6P213E0.book  Page 1  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands