manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 25

Basic components

19

EMU31420

Top cowling lock lever (pull up type)

To remove the top cowling, pull up the lock le-
ver(s) and lift off the cowling. To install the top
cowling, place it in its original position, and
then move the lever(s) downward to lock it in
place.

NOTE:

●

When installing the cowling, check to be
sure it fits properly in the rubber seal.

●

Be sure to check that the gap between the
top cowling and the bottom cowling is even
all around the cowling. If the top cowling is
loose or the gap is not even, reinstall the
cowling.

EMU26460

Flushing device

This device is used to clean the cooling water
passages of the motor using a garden hose
and tap water.

NOTE:

For details on usage, see page 50.

EMU31702

Water separator

This engine has a combination fuel filter/water
separator and associated warning system. If
water separated from the fuel exceeds a spe-
cific volume, the warning device will activate.

Activation of warning device

1. Flushing device

U6P213E0.book  Page 19  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands