Yamaha F250 Owner'S Manual Download Page 51

Page: 51 / 90

Operation

EMU28055

Procedure for tilting down (power trim
and tilt models / power tilt models)

Push the power trim and tilt switch / pow-
er tilt switch “

” (up) until the outboard

motor is supported by the tilt rod and the
tilt support lever / tilt support knob be-
comes free.

Release the tilt support lever or pull out
the tilt support knob.

Push the power trim and tilt switch / pow-
er tilt switch “

” (down) to lower the out-

board motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU30710

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially
to allow operation in shallow water.

ZMU01884

ZMU01885

ZMU04196

ZMU04603

U6P213E0.book Page 45 Thursday, March 9, 2006 10:20 AM

Summary of Contents for F250



























































































Search results

Summary of Contents for F250

Reviews:

Related manuals for F250

Brands by name

Popular brands

Yamaha F250, Owner'S Manual

Search results

Summary of Contents for F250

Reviews:

Related manuals for F250

Brands by name

Popular brands