manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 63

Maintenance

57

CAUTION:

ECM01240

Change the engine oil after the first 10
hours of operation, and every 100 hours or
at 6-month intervals thereafter. Otherwise
the engine will wear quickly.

NOTE:

Change the engine oil when the oil is still
warm.

The engine oil can be extracted with an oil
changer (recommended), or drained by re-
moving the oil drain screw.
Extracting the oil with an oil changer (normal
oil change)
1.

Put the outboard motor in an upright po-
sition (not tilted).

2.

Pull out the dipstick and use the oil
changer to extract the oil.

3.

Remove the oil filler cap. Add the correct
amount of oil through the filler hole, and
install the filler cap.

CAUTION:

ECM00970

●

Do not overfill the oil, and be sure the
outboard motor is upright (not tilted)
when checking and changing the engine
oil.

●

If the oil level is above the upper level
mark, drain until the level meets the
specified capacity. Overfilling the oil
could cause leakage or damage.

4.

Remove oil dipstick and wipe it clean.

5.

Completely insert the dipstick and re-
move it again.

6.

Check the oil level using the dipstick to be
sure the level falls between the upper lev-
el mark “ ” and lower level mark “ ” . Fill
with oil if it is below the lower level mark
“ ” , or drain to the specified level if it is
above the upper level mark “ ” .

1. Oil filler cap

Recommended engine oil:

4-stroke outboard motor oil

Engine oil quantity (excluding oil filter):

5.6 L (5.92 US qt) (4.93 Imp.qt)

U6P213E0.book  Page 57  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands