Yamaha F250 Owner'S Manual Download Page 81 | Manualshive

Page: 81 / 90

background image

Trouble Recovery

75

9.

Fasten the water detection switch lead
with the holder.

10. Install the top cowling.
11. Start the engine and make sure that the

water separator warning indicator re-
mains off.

NOTE:

Have a Yamaha dealer inspect the outboard
motor after returning to port.

EMU29760

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immediate-
ly.
If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-
dure below in order to minimize engine dam-
age.

EMU29970

Procedure

1.

Thoroughly wash away mud, salt, sea-
weed, and so on, with fresh water.

2.

Remove the spark plugs and face the
spark plug holes downward to allow any
water, mud, or contaminants to drain.

3.

Drain the fuel from the vapor separator,
fuel filter, and fuel line.

4.

Spray “Fogging Oil” or supply engine oil
through the intake manifold and spark
plug holes while rotating the flywheel
manually.

5.

Take the outboard motor to a Yamaha
dealer as soon as possible.

CAUTION:

ECM00400

Do not attempt to run the outboard motor
until it has been completely inspected.

1. Holder

U6P213E0.book Page 75 Thursday, March 9, 2006 10:20 AM

«
...
79
80
81
82
83
...
»

Summary of Contents for F250



























































































Reviews:

No comments

Related manuals for F250

Brand: ULPOWER Pages: 25

Brand: Beckhoff Pages: 31

Brand: Briggs & Stratton Pages: 6

Lombardini LGW 523 MPI

Brand: Kohler Pages: 144

Brand: IMS Pages: 6

Brand: MTD Pages: 44

Command Pro EFI ECH940

Brand: Kohler Pages: 8

Courage PRO SV810

Brand: Kohler Pages: 20

KDI 3404TCR-SCR

Brand: Kohler Pages: 64

Brand: Kohler Pages: 88

Brand: Kohler Pages: 334

Brand: XTM Racing Pages: 6

Brand: YS Pages: 2

Megatorque PS Series

Brand: NSK Pages: 370

Brand: Franklin Pages: 114

Brand: Cors-Air Pages: 10

Brand: Power smart Pages: 28

Brand: A'OK Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands