manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 80

Trouble Recovery

74

4.

Disconnect the water detection switch
coupler.

CAUTION:

ECM01570

Be careful not to get any water on the wa-
ter detection switch coupler, otherwise a
malfunction could occur.

5.

Unscrew the filter cup from the filter hous-
ing.

NOTE:

Be careful not to twist the water detection
switch lead when unscrewing the filter cup.

6.

Drain the water in the filter cup by soaking
it up with a rag.

NOTE:

Properly dispose of the rag.

7.

Firmly screw the filter cup onto the filter
housing.

NOTE:

Be careful not to twist the water detection
switch lead when screwing the filter cup onto
the filter housing.

8.

Connect the water detection switch cou-
pler securely until a click is heard.

1. Holder

1. Water detection switch coupler

1. Filter cup

2. Water detection switch lead

1. Water detection switch coupler

U6P213E0.book  Page 74  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands