manualshive.com logo in svg

Yamaha F250, Owner'S Manual

Share
Download
Yamaha F250 Owner'S Manual Download Page 3

Important manual information

EMU31280

To the owner

Thank you for choosing a Yamaha outboard
motor. This Owner’s Manual contains infor-
mation needed for proper operation, mainte-
nance and care. A thorough understanding of
these simple instructions will help you obtain
maximum enjoyment from your new Yamaha.
If you have any question about the operation
or maintenance of your outboard motor,
please consult a Yamaha dealer.
In this Owner’s Manual particularly important
information is distinguished in the following
ways.

 The Safety Alert Symbol means AT-

TENTION! BECOME ALERT! YOUR SAFE-
TY IS INVOLVED!

WARNING

EWM00780

Failure to follow WARNING instructions
could result in severe injury or death to the
machine operator, a bystander, or a per-
son inspecting or repairing the outboard
motor.

CAUTION:

ECM00700

A CAUTION indicates special precautions
that must be taken to avoid damage to the
outboard motor.

NOTE:

A NOTE provides key information to make
procedures easier or clearer.

Yamaha continually seeks advancements in
product design and quality. Therefore, while
this manual contains the most current product
information available at the time of printing,
there may be minor discrepancies between

your machine and this manual. If there is any
question concerning this manual, please con-
sult your Yamaha dealer.

NOTE:

The F250TR, LF250TR and the standard ac-
cessories are used as a base for the explana-
tions and illustrations in this manual.
Therefore some items may not apply to every
model.

EMU25110

F250, LF250

OWNER’S MANUAL

©2006 by Yamaha Motor Corporation, 

USA

1st edition, March 2006

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, USA

is expressly prohibited.

Printed in Japan

P/N LIT-18626-07-16

U6P213E0.book  Page 1  Thursday, March 9, 2006  10:20 AM

Summary of Contents for F250



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands