Yamaha F250 Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 90

background image

Basic components

23

NOTE:

The clock operates on battery power. Discon-
necting the battery will stop the clock. Reset
the clock after connecting the battery.

EMU26710

Fuel gauge

The fuel level is indicated by eight segments.
When all segments are showing, the fuel tank
is full.

CAUTION:

ECM00860

The Yamaha fuel tank sensor differs from
conventional sensors. Incorrectly setting
the selector switch on the gauge will give
false readings. Consult your Yamaha deal-
er on how to correctly set the selector
switch.

NOTE:

The fuel level reading can be affected by the
position of the sensor in the fuel tank and the
attitude of the boat in the water. Operation
with bow-up trim or continuous turning can
give false readings.

EMU26720

Fuel warning indicator

If the fuel level decreases to one segment, the
fuel level warning segment will begin to blink.

CAUTION:

ECM00880

Do not continue to operate the engine with
full throttle if a warning device has activat-
ed. Get back to the port within trolling en-
gine speed.

EMU26730

Low battery voltage warning indicator

If battery voltage drops, the display will auto-
matically turn on and begin to blink.

CAUTION:

ECM00870

Get back to the port soon if a warning de-
vice has activated. For charging the bat-
tery, consult your Yamaha dealer.

1. Fuel level warning segment

ZMU01745

U6P213E0.book Page 23 Thursday, March 9, 2006 10:20 AM

«
...
27
28
29
30
31
...
»

Summary of Contents for F250



























































































Reviews:

No comments

Related manuals for F250

Brand: J.A.P Pages: 21

Brand: Dynamite Pages: 28

Brand: Yanmar Pages: 14

Brand: Yanmar Pages: 52

Brand: Yanmar Pages: 66

Brand: Yanmar Pages: 264

Brand: Yanmar Pages: 350

Throttling Governor Kerosene Stationary Engines

Brand: Worthington Pages: 33

Enduro RR 350 2015

Brand: Beta Pages: 158

Brand: INDUSTRIAS TECHNOFLEX Pages: 40

Brand: Saito Pages: 5

Brand: Saito Pages: 6

Brand: YS Pages: 2

130000 950 Series

Brand: Briggs & Stratton Pages: 100

Brand: VACGEN Pages: 13

Brand: Turn Key Pages: 16

Brand: Nanni Pages: 32

Brand: California Air Tools Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands